Please use side menu if you cannot use dropdown boxes, or the header boxes


www.ccr.gov
CAGE Code: 5DME2
ITAR Registration Code: M28889

- April 23rd 2017 -
Call: 1 (800) 377-3244
We Are Open Monday-Friday 8 am - 5 pm PT
E-mail: sales@coilws.com


Toroidal Power Transformers


Toroidal Power Transformers are made with tape wound cores. The tape wound cores provide an almost perfect magnetic circuits to minimize losses, fringing, leakage, distortion, and provide good magnetic shielding. It also decreases the magnetization force required to produce a given flux density. It is much more efficient than E-type lamination cores, but will have somewhat higher cost as the windings need to be done on the core itself, rather than on a bobbin. The tape material is made of insulated, high permeability silicon iron, with a typical thickness of 4 mils ( 0.004"). Other materials types such as 50% nickel iron alloy, Molybdenum permalloy or supermendor are also available with increased cost.

Coil Winding Specialist (CWS) has designed a series of low cost standard tape wound transformers as shown in the table "Toroidal Power Transformer - How to order ". All these transformers are designed to meet all international safety requirements ( UL, CSA, TUV, etc). Customer can order these standard transformers in small quantities for testing and prototyping.

Please click on the link below to view the complete specifications and standard off the shelf parts and ordering infromation.

 

FEATURES

 

  • 10VA to 750VA Power levels
  • Low magnetic noise
  • Very low no load losses and magnetizing current
  • High Efficiency due to the toroidal structure
  • Excellent Load Regulation
  • Meets UL, CSA, VDE Requirements
  • Hi-Pot: 4000 Vrms
  • Dielectric breakdown: Over 3000V, 1 min between primary and secondary
  • Insulation System: Class B, 130°C
  • Easy installation or assembly
  • Available with various input voltages: 100V, 110V, 117V, 120V, 220V, 230V, 240V. All in 50 - 400Hz
  • Standard with single primary winding. Dual primary is available as an option
  • 100% factory tested for all parameters
  • Mounting hardware accessory options are
    available upon request.
    • Mounting Hardwares include :-
          Metal washer
          Silicone rubber pads
          Plastic washer (UL-94V0)
          Screws/nuts

    If none of the standardized transformers listed in the following table can meet your needs, we can provide custom design to meet your specific needs with a minimal NRE charge.


 


Toroidal Power Transformers - How to order

 


Disclaimer: Coil Winding Specialist, Inc., its affiliates, agents, and employees acting on behalf of Coil Winding Specialist, Inc. (collectively, CWS) disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. CWS reserves the right at any time and from time to time to make changes to design, technical specification, or construction of any product listed on this website without notice. CWS also reserves the right to discontinue or limit sale of any product or service available throughout this website on temporary or permanently basis without notice. CWS highly recommends customers not to use its products offered on this website for inappropriate use and applications. Products should be tested for its suitability by prospective customers in all possible applications and conditions. Customers using or selling CWS products for use in other than recommended applications do so entirely at their own risk and agree to fully indemnify CWS from any damages arising or resulting from such use or sale.


Any Comments, Suggestions or Questions? Contact us! Email: sales@coilws.com
CWS 353 West Grove Ave. Orange, California 92865
Call us Toll Free: 1-800-679-3184 or 1 (800) 377-3244

Tel: (714) 279-9010, Fax: (714) 279-9482

Copyright 2008, Coil Winding Specialist, Inc
Updated July, 2013

CAGE Code: 5DME2(Registered with www.ccr.gov)