---- December 5th 2024 ----

www.ccr.gov
CAGE Code: 5DME2
ITAR Registration Code: M28889
Call: 1 (800) 377-3244
Monday to Friday 8 A.M. - 5 P.M. (Pacific Time)
E-mail questions and requirements to: sales@coilws.com

Pricing is subject to change depending on product availability and backorders.
*Please Note: Items without price are listed for CWS' capability purposes.

Environmental Specification



Environmental and Test Specifications for Surface Mount Power Inductors

1. Operational Temperature
  • Ambient temperature of - 25°C to +80°C (The coil will dissipated heat from its resistance). Please contact factory if higher temperature is needed.
2. External Appearance
  • On visual inspection, the surface mount power inductors should have no visible external defects.
3. Terminal Strength
  • After soldering, the surface mount inductor/ choke should withstand the following test:
  1. A force of 5N ( 0.15 K GF) is applied for 10 + -2 seconds between copper trace and the soldered coil in the X direction.
  2. A force of 5N ( 0.15 K GF) is applied for 10 + -2 seconds between copper trace and the soldered coil in the Y direction.
  3. The terminal should not peel off when 1 and 2 are executed. Refer to figure at right.
4. Heat Endurance Test
5. Dielectric Strength
  • No di-electric breakdown when a 100V DC. is applied for 1 minute between the coil (winding) and the core.
6. Insulating Resistance
  • Over 100M ohms at 100V DC. between the coil and the core.
7. Inductance Temperature Coefficient
  • (0 ~ 2000) x 10-6 /°C . At ambient tempertaure of -25°C to +80 °C
8. Humididty Test
  • Inductance deviation is within + - 5% after 96 hours in a 90 to 95% relative humidity at 40 + -2°C and a 1 hour drying period under normal conditions.

9. Vibration Test

  • Inductance deviation is within + - 3.0% after a vibration period of 1 hour in each of the 3 orientations sweep vibration (10~55~10Hz) with a 1.5mm peak to peak amplitude.
10.Shake / Drop Test
  • Inductance deviation is within + - 3.0% after a drop down with a 981 m/s2 (100G) shack attitude upon a rubber block type of shock testing machine. Duration of 1 time, in each of the 3 orientations.
 

Disclaimer: Coil Winding Specialist, Inc., its affiliates, agents, and employees acting on behalf of Coil Winding Specialist, Inc. (collectively, CWS) disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. CWS reserves the right at any time and from time to time to make changes to design, technical specification, or construction of any product listed on this website without notice. CWS also reserves the right to discontinue or limit sale of any product or service available throughout this website on temporary or permanently basis without notice. CWS highly recommends customers not to use its products offered on this website for inappropriate use and applications. Products should be tested for its suitability by prospective customers in all possible applications and conditions. Customers using or selling CWS products for use in other than recommended applications do so entirely at their own risk and agree to fully indemnify CWS from any damages arising or resulting from such use or sale.

WARNING: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go towww.P65Warnings.ca.gov.


Any Comments, Suggestions or Questions? Contact us!
Email: sales@coilws.com
CWS 353 West Grove Ave. Orange, California 92865
Call us Toll Free: 1-800-679-3184 or 1 (800) 377-3244

Tel: (714) 279-9010, Fax: (714) 279-9482

Copyright 2008, Coil Winding Specialist, Inc
Updated July, 2013

CAGE Code: 5DME2(Registered with www.ccr.gov)